|    Sitemap    |    Contact Us    
 
 
D1700 Series Command Set
 
The DGH D1700 series products use a simple command and response protocol. A module must be interrogated by a host computer to obtain data. A module will never initiate a command sequence in order to prevent communications collisions.

A command is initiated with a command prompt, may be a dollar sign ($) or pound sign (#). Following the prompt a single address character must be transmitted. Each module on a communications bus must be setup with a unique address. The address is followed by a two character command. Every command is terminated with a carriage return.

The module response begins with a response prompt, which is an asterisk (*) followed by the necessary data. Every response is terminated with a carriage return. Linefeeds after the carriage return are user selectable. See the table below for typical commands and their respective response messages.


Command Definition Typical Command  Typical Response 
ACK - Acknowledge $1ACK *
CB - Clear Bit $1CB0C *
CP - Clear Position $1CP12 *
DI -  Digital Input $1DI *0007
DO -  Digital Output $1DO1234 *
RA - Read Assignments $1RA *0F0F
RAB - Read Assignment Bit $1RAB0E *O
RAP - Read Assignment Position $1RAP14 *I
RB - Read Bit $1RB0E *1
RD - Read Data $1RD *+99999.99
RE - Read Event Counter $1RE *0001107
RID - Read IDentification $1RID *BOILER
RIV - Read Initial Value $1RIV *0F0F
RP - Read Position $1RP14 *0
RS - Read Setup $1RS *31070002
RSU - Read Setup $1RSU *31070002
RWT - Read Watchdog Timer $1RWT *+00010.00
SB - Set Bit $1SB0C *
SP - Set Position $1SP12 *
WE - Write Enable $1WE *
     
Write Protected Commands    
AIB - Assign Input Bit $1AIB0E *
AIO - Assign Input/Output $1AIO0F0F *
AIP - Assign Input Position $1AIP14 *
AOB - Assign Output Bit $1AOB0E *
AOP - Assign Output Position $1AOP14 *
CE - Clear Events $1CE *
EC - Events Clear $1EC *0000100
ID - IDentification $1IDBOILER *
IV - Initial Value $1IV0F0F *
RR - Remote Reset $1RR *
SU - Setup  $1SU310701C2 *
WT - Watchdog Timer $1WT+00010.00 *
     
Continuous Input/Output Mode Commands    
CIA - Set Continuous Input Address $1CIA31 *
CMC - Continuous Mode Change $1CMC *
CMD - Continuous Mode Disable $1CMD *
CME - Continuous Mode Edge Triggered $1CME *
CMT - Continuous Mode Timer $1CMT *
CT - Continuous Time (Set Time) $1CT+00010.00 *
RCM - Read Continuous Mode $1RCM *D,T,E,C
RCT - Read Continuous Time Variable $1RCT *+00010.00
RIA - Read Continuous Input Address $1RIA *31

Notes:
1. The D1711 and D1712 modules utilize the D1700 series command set. Click here to view the D1700 command set.
2. The D1701 and D1702 modules utilize the D1000 series command set. Click here to view the D1000 command set.
 
Modbus Products
ASCII Products
Accessories
Support
Purchase
Company  
  D1000M Series
  D1700M Series
  D3000M Series
  D5000M Series
  DIN-100 Series
  D6000 Series
  D7000 Series
  D8000 Series
  D1000 Series
  D1700 Series
  D2000 Series
  D3000 Series
  D4000 Series
  D5000 Series
  Mounting Backplanes
  Module Accessories
  Serial Converters
  USB Converter
  Power Supplies
  Software
  Cables
  FAQ's
  Data Sheets
  Diagrams
  User Manuals
  Product Finder
  Modbus Support
  Contact Support
  Product Warranty
  How to Buy
  Shop Online
  International
  View Shopping Cart
  About Us
  Contact Us
  Policies
  Sitemap
  Blog
  Join our Email List

          
 
 
Copyright Dutile, Glines & Higgins Corporation,
All Rights Reserved.